User Tools

Site Tools


products:pcie_screamer

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
products:pcie_screamer [2019/01/31 20:34]
po [PCIe Screamer (R01 & R02)]
products:pcie_screamer [2019/07/10 18:08] (current)
po [Quick Start]
Line 1: Line 1:
 ====== PCIe Screamer (R01 & R02)====== ====== PCIe Screamer (R01 & R02)======
  
-{{ :products:r02_01_cut.jpeg?400 |}}+{{ :products:pcie_screamer:​dsc_0989_small.jpg?500 |}}
  
 Buy it on our shop: Buy it on our shop:
-  * R02: [[http://​shop.lambdaconcept.com/​home/​32-pciescreamerR02.html|Buy PCIe Screamer R02]] +  ​* **R02:** [[http://​shop.lambdaconcept.com/​home/​32-pciescreamerR02.html|Buy PCIe Screamer R02]] 
-  * R01: [[http://​shop.lambdaconcept.com/​home/​11-pciescreamer.html|Buy PCIe Screamer]]+  ​* <​del>​**R01:** [[http://​shop.lambdaconcept.com/​home/​11-pciescreamer.html|Buy PCIe Screamer]] ​Deprecated</​del>​
  
 ===== Description ===== ===== Description =====
  
-==== Features ====+==== Features ​& Specifications ​====
  
-  * XC7A35T ​Xilinx 7 Series FPGA +  * **FPGA Chipset:​** ​Xilinx 7 Series ​XC7A35T 
-  * FT601 FTDI USB 3.0 +  * **Memory:​** 
-  * MT41K256 4Gb DDR3 DRAM +    * 4Gb DDR3 DRAM MT41K256  
-  * PCIe Gen2 X1+    * 256Mb SPI Flash for FPGA self-configuration 
 +  * **USB Chipset:​** ​USB 3.0 FTDI FT601 
 +  * **PCIe Bandwidth:​** PCIe x1 Gen 2.0: 5GT/s 
 +  * **System Clock:** Frequency: 100 MHz 
 +  * **User Interfaces:​** 
 +    * 2 x LED 
 +    * 2 x push button 
 +  * **Serial Interface:​** USB to UART FTDI FT232 
 +  * **JTAG:** 6 pins JTAG connector for FPGA programming 
 +  * **Input Voltage:** 12V from PCIe or from external supply 
 +  * **GPIO:** 2 pins + GND 
 +  * **Dimensions:​** 130 mm x 110 mm x 12 mm
  
-==== Power Supply ​====+==== Hardware revisions ​====
  
-CN5 jumper selects the power source.+  * **R02:** 
 +    * PCIe lanes routing has been improved with better differential pairs impedance and length matching. 
 +    * Better PCIe signal stability. 
 +    * Existing software and gateware are fully compatible with this new version.
  
-  * Power Jack (5 to 15 V): Tie middle and right pins. +==== Buttons ====
-  * PCIe Power: Tie middle and left pins.+
  
-{{:products:img_9512_small_zoom_jumper.jpg?​200|}}+  * **SW1:** FPGA Program/​Reset 
 +  * **SW3:** User Button 
 +  * **SW4:** User Button
  
-==== Boot modes ====+==== LEDs ====
  
-SW2 selects the FPGA bootmode. Set it to Master SPI:+  * **LD1:** User Led (Green) 
 +  * **LD2:** User Led (Green) 
 +  * **LD3:​** ​FPGA Prog Done (Green) 
 +  * **LD4:** Power Good (Red)
  
-=== Master SPI ===+===== Quick Start =====
  
-  ​* 1: ON +**1. Select power source:** 
-  2: OFF +    For PCIe power supply, put the jumper on the left position. 
-  3OFF+    For External supply via jack CN4, put the jumper on the right position. Input voltage5V to 15V max.
  
-{{:​products:​img_9512_small_zoom_switch.jpg?200|}}+{{:​products:​pcie_screamer:​r02_power.png?200|}}
  
-==== LEDs ====+When the power supply is stable, the LED LD4 will be red.
  
-  ​LD1: User Led (Green) +**2. Select Boot mode (R01 only)**
-  ​LD2: User Led (Green) +
-  ​LD3: FPGA Prog Done (Green)+
  
-{{:products:​img_9512_small_zoom_leds.jpg?​200|}}+SW2 selects the FPGA bootmode. Set it to Master SPI:
  
-  * LD4Power Good (Red)+  * 1ON 
 +  * 2: OFF 
 +  * 3: OFF
  
-{{:​products:​img_9512_small_zoom_power.jpg?200|}} +{{:​products:​img_9512_small_zoom_switch.jpg?200|}}
- +
-==== Buttons ==== +
- +
-  * SW1: FPGA Program +
-  * SW3: User Button +
-  * SW4: User Button+
  
 +Once booted, FPGA prog done LED LD3 will be green.
 ===== Gateware & Software ===== ===== Gateware & Software =====
  
products/pcie_screamer.1548963286.txt.gz · Last modified: 2019/01/31 20:34 by po